称重传感器

称重传感器
称重传感器

产品类别

联系方式

电话:0755-26738591

传真:0755-26998440

网址:http://www.octsources.com

邮箱:sales@octsources.com

地址:深圳市南山区南头街道虹步路39号马家龙14栋大习科创大厦

产品类别 > 红外多分析仪 > IRMA 红外多分析仪

IRMA 红外多分析仪

所属品牌:日本千野CHINO温湿度传感器 来源:深圳市现代豪方仪器仪表点击:1607次发布时间:2020-05-08

日本千野,IRMA,红外多分析仪


IRMA 红外多分析仪

IRMA 红外多分析仪PDF资料:IRMA 红外多分析仪产品资料


品牌:日本CHINO

型号:IRMA

类型:红外多分析仪

 特点

10波长,4组分,高速/高重复性,多接口,操作方便

IM系列

是一种在线多红外波长分析仪,利用红外吸收技术测量,产品成分和/或厚度。信号处理功能内置于紧凑的一体式探测器中易于安装和操作的装置。最多99校准曲线可存储在探测器存储器中用于多种测量应用。探测器可以自行使用或连接到PC/工厂控制系统,提供模拟和数字输出。遥控器设置显示单元,最多可连接9个探测器单位,可用于设置各种探测器功能和还显示测量值。

特征

●最多10个波长,可测量4种成分

例如:水分、膜厚、有机物和涂层厚度同时实时。

●连接到多个接口、RS485(MODBUS)、以太网(局域网)

●高速高重复性(28ms)

●多计算功能

●自诊断功能,维护方便。

●符合CE标准和IP-65

应用

●测量木屑的水分。

●测量薄板或薄膜的厚度。

●测量生物、水分和脂质饲料。

●测量土豆的有机物、水分和油脂炸薯条。

●测量垃圾湿度(RDF湿度)。

●测量油漆上的涂层厚度工作表。

●测量粉末的水分。

●测量清洗液中的水分。

●测量粘土的水分。

●测量纤维的水分。

●测量和控制层压板的涂层厚度-薄板生产线。

●测量和控制油漆厚度。

 IRMA系列类型

●1000系列…湿度(镜面)

11:一般湿度

12:高湿度

13:微水分

2000系列…湿度(纤维型)

21:一般湿度

22:高湿度

●5000系列…多部件(镜式)

51:多组分(NIR)

52:多组分(薄膜、红外)

●6000系列…多组分(纤维型)

61:多组分

●7000系列……厚度,涂层(镜面)

71:厚度,涂层(NIR)

72:薄膜,涂层(红外)

●8000系列……厚度,涂层(纤维型)

81:厚度,涂层

测量波长或分量的数量

00:5000&6000系列以外

□□:适用于5000和6000系列

:测量波长数:2到0(10)

:测量元件数量:1至4

通信接口

S:RS485(标准)*1

L:以太网(LAN)

W: SS收音机

特殊规格*2

空白:标准

1:小直径型

2:防锈型

3:增益规格

4:P偏振光

*1: 选择L,W时,RS485不适用。

*2: 模型中还有其他特殊应用。

测量示例(表1)

对象

范围

累计

总湿度%

玻璃/陶器/水泥

陶土

0 to 12

>±0.3

铁/金属

0 to 15

>±0.2

混合原料

0 to 10

>±0.2

氧化铁

0 to 10

>±0.2

食品

淀粉

0 to 25

>±0.2

面包屑

0 to 20

>±0.2

大豆

0 to 15

>±0.2

奶粉

0 to 5

>±0.2

糖/盐

0 to 2

>±0.05

调味品

0 to 10

>±0.2

茶叶

0 to 15

>±0.2

化学制品

催化剂

0 to 10

>±0.2

中等

0 to 20

>±0.2

洗涤剂

0 to 15

>±0.2

墨水

0 to 5

>±0.2

肥料

0 to 5

>±0.2

橡胶/纤维等

维尼纶纤维

0 to 10

>±0.2

腈纶

0 to 10

>±0.2

木屑

0 to 10

>±0.2

纸类

0 to 10

>±0.1

表2

高水分%

石膏

to 15

>±0.7

湿纸

40 to 70

>±0.5

生面包屑

30 to 40

>±0.7

粘土

0 to 30

>±0.3

硅砂

0 to 10

>±0.8

碳酸氢盐

0 to 18

>±0.6

微水分%

ABS、PVC粉

0 to 1

>±0.08

粒状铁素体

0 to 0.5

>±0.09

厚度(μm)

聚乙烯聚乙烯

10 to 3000

>±0.2

聚丙稀

 

>±0.2

聚酯聚酯

 

>±0.2

聚氯乙烯

 

>±0.2

聚乙烯醇

 

>±0.2

经济增加值

 

>±0.2

聚苯乙烯

 

>±0.2

聚碳酸酯

 

>±0.2

尼龙PA

 

>±0.2

聚酰亚胺

 

>±0.3

产三醋酯纤维膜片

 

>±0.2

涂层(g/m2)

涂层纸

10 to 1000

>±0.2

折叠纸、标签

 

>±0.2

湿/干粘合剂

 

>±0.2

钢板树脂

 

>±0.2

通用规范

红外多分析仪

测量系统:红外吸收式

测量波长:

最多10个波长

测量部件:

多达4种成分

光源:钨灯

测量距离:200至400 mm

IRMA1300:160至300毫米)

测量直径:50 mm□/300 mm

IRMA1300:30mm□/200m)

模拟输出:4至20mADC,满量程的±0.2%

(负载电阻:小于500Ω)

通信:RS485 MODBUS

输出更新周期:28ms

显示和设置:显示数据和设置参数

参数可按键配置

计算:2或3色比计算

多元回归计算

校准曲线数量:最多99条曲线

校准曲线:线性、二次、三次、多元回归线

校准曲线校正:线性和二次校正

平滑(延迟):0到99秒

校准:通过检查板

探测器编号设置:当多个探测器工作时,

探测器编号是可配置的

通道号设置:校准曲线号是关键配置。

自诊断:当

异常情况

校正输入:补偿测量值

通过外部4至20毫安直流电

(样品温度等)

外部Di/o:Di(触点输入)--执行任一预设,

数据保持或真实/平滑

Do(触点输出)--选择self

-诊断(1b)或高/低报警(1a)

工作温度:

0至50°C(如果高于45°C,则使用干空气冷却

出口空气温度必须低于30°C)

电源:由IR-WEP提供24伏直流电

IR-WEP电源:100-240VAC)

功耗:约30VA

连接:端子连接

外壳:铝铸件,防滴漏结构(符合

符合IEC529,IP65)

重量:约4.3kg

安装:螺栓悬挂法,4个M8螺栓

CE标准:EN61326-1:2006

排放:A级

抗扰度:表2

设置显示单元

输入信号:RS485,最多可连接9个探测器

模拟输出:4至20毫安直流电,3输出(负载电阻:

输出1,2:小于600Ω,3:小于400Ω)

1号至3号探测器的1号部件输出用于

多头)

通信:RS232C(标准)、RS422A或RS485(可选)

输出更新周期:

28ms x探测器编号

显示:1。测量数据,LED 5位

2。探测器号、部件号、校准曲线

编号,参数设置

(探测器多元件显示元件号

米)

探测器编号设置:探测器编号1至9是可配置的

部件号设置:

组件1到4是可配置的密钥

(取决于探测器)

校准曲线编号设置:

校准曲线编号是每个

探测器编号,也可通过外部触点配置

平滑时间:平滑计算时的平滑时间设置

T=0.0至9.9,10至99秒

校准功能:通过按键操作或外部校准

检查板使用中的触点

保持/预设:保持或预设显示和按键输出

操作或外部接触

校正曲线:

校准曲线的在线校正

语言矫正

外部设置:探测器编号、组件编号、校准曲线编号。,

校准、保持或预设

报警功能:高/低限报警单个触点输出(a

触点,公共)超出设定范围

自诊断:异常时输出接点信号(1b)

外壳材料:阻燃聚碳酸酯

工作环境:0至50摄氏度

安装:面板安装式

重量:约0.6kg

电源:100至240V AC 50/60Hz

最大功耗20VA

CE标准:EN61326-1:2006

排放:A级

抗扰度:表2

光纤单元

测量距离和直径:

配透镜---φ25/25mm~φ40/100mm

无透镜---φ20/15mm至φ50/50mm

光纤长度:标准1.5m,最大5m(反射型光纤)

标准2m,最大10m(传输型光纤)

纤维防护:不锈钢柔性装甲

最小弯曲半径:

100毫米

工作温度:

0至150摄氏度

吹扫空气流量:带镜头---空气吹扫禁用

无镜头---5至20L/min

附件:垂直安装支架

法兰固定器

特殊规格

规格

内容

小直径

镜面反射式30mm

防锈

用于内部印刷电路板

增益规格

特殊样品

P偏振光

样品检验判定


外形尺寸


英文版

0-wavelength, 4-constituent, High-speed/High-repeatability, Multi-interface, Easy to operate

The IM series is an on-line multi IR wavelength analyzer

utilizing the infrared absorption technology for measuring

product constituent and/or thickness. Signal processing

capabilities are built into the compact all-in-one detector

unit for easy installation and operation. A maximum of 99

calibration curves can be stored into the detector memory

for numerous measurement applications. The detector can

be used by itself or connected to a PC/plant control system,

as both analog and digital outputs are provided. A remote

setting display unit, connectable up to 9 detector

units, can be used to setup various detector functions and

also displays measured values.

FEATURES

●Up to 10 wavelengths, capable of measuring 4 constituents

such as; moisture, film-thickness, organism, and coating-thickness

in real time simultaneously.

●Connectivity to multiple interfaces, RS485 (MODBUS), Ethernet

(LAN)

●High-speed & High-repeatability (28ms)

●Multi-calculation function

●Self-diagnostic function, easy maintenance.

●Conforms to CE standards and IP-65

APPLICATION

●Measuring moisture of wood chip.

●Measuring the thickness of sheet or film.

●Measuring the organism, moisture and lipid of

fodder.

●Measuring the organism, moisture and oil of potato

chips.

●Measuring moisture of garbage (RDF moisture).

●Measuring the coating thickness on the painting

sheet.

●Measuring moisture of powder.

●Measuring moisture in cleaning solution.

●Measuring moisture of clay.

●Measuring moisture of fiber.

●Measure & Control the coating thickness of Laminate-

sheet production line.

●Measure & Control the painting thickness.

MEASURING EXAMPLES(Table 1

Object

Range

Accu

General moisture (%)

Glass / pottery / cement

Potter's clay

0 to 12

>±0.3

Iron / metal

Coal

0 to 15

>±0.2

Mix raw material

0 to 10

>±0.2

Iron oxide

0 to 10

>±0.2

Foods

Starch

0 to 25

>±0.2

Bread-crumbs

0 to 20

>±0.2

Soybean

0 to 15

>±0.2

Milk powder

0 to 5

>±0.2

Sugar / salt

0 to 2

>±0.05

Flavouring

0 to 10

>±0.2

Tea

0 to 15

>±0.2

Chemicals

Catalyst

0 to 10

>±0.2

Medium

0 to 20

>±0.2

Detergent

0 to 15

>±0.2

Ink

0 to 5

>±0.2

Fertilizer

0 to 5

>±0.2

Rubber / fiber / etc.

Vinylon fiber

0 to 10

>±0.2

Acrylic fiber

0 to 10

>±0.2

Wood chip

0 to 10

>±0.2

Paper

0 to 10

>±0.1

Table 2

High moisture (%)

Plaster

5 to 15

>±0.7

Wet paper

40 to 70

>±0.5

Raw bread crumbs

30 to 40

>±0.7

Clay

0 to 30

>±0.3

Silica sand

0 to 10

>±0.8

Bicarbonate

0 to 18

>±0.6

Micro moisture (%)

ABS, PVC powder

0 to 1

>±0.8

Granularferrite

0 to 0.5

>±0.8

Thickness (μm)

Polyethylene PE

10 to 3000

>±0.2

Polypropylene PP

 

>±0.2

Polyester PET

 

>±0.2

Vinyl chloride PVC

 

>±0.2

PVA

 

>±0.2

EVA

 

>±0.2

Polystyrene PS

 

>±0.2

Polycarbonate

 

>±0.2

Nylon PA

 

>±0.2

Polyimide PI

 

>±0.3

TAC film

 

>±0.2

Coating (g/m2)

Coat-paper

10 to 1000

>±0.2

Tuck-paper, label

 

>±0.2

AdhesiveWET/DRY

 

>±0.2

Resinonsteel-board

 

>±0.2

■GENERAL SPECIFICATIONS

Measuring system: Infrared absorption type

Measuring wavelength:

Up to 10 wavelengths

Measuring component:

Up to 4 constituents

Light source: Tungsten lamp

Measuring distance: 200 to 400mm

(IRMA1300: 160 to 300mm)

Measuring diameter:50mm□/300mm

(IRMA1300:30mm□/200m)

Analog output: 4 to 20mADC, ±0.2% of full scale

(Load resistance: less than 500Ω)

Communications: RS485 MODBUS

Output renewal cycle: 28ms

Display & setup: Displays data & setup parameter

Parameters are configurable by key

Computing: 2 or 3-color ratio calculation

Multiple regression calculation

No. of calibration curve: Up to 99 curves

Calibration curve: Linear, quadratic, cubic & multiple regression line

Calibration curve correction: Linear & quadratic correction

Smoothing (delay): 0 to 99 seconds

Calibration: By checking plate

Detector No. setup: When multiple detector operation,

detector No. is key configurable

Channel No. setup: Calibration curve No. is key configurable.

Self-diagnostic: Outputs contact signal and communications when 

abnormal conditions

Correction input: Compensate measured value

by external 4 to 20mA DC

(sample temperature, etc.)

External Di/o: Di(contact input) --- Perform either one of preset,

data-hold or real/smoothing

Do(contact output) --- Selects self

-diagnostic(1b) or Hi/low alarm(1a)

Working temperature:

0 to 50°C (Use dry air cooling if higher than 45°C

Outlet air temperature must be lower than 30°C)

Power supply: 24V DC supplied from IR-WEP

(IR-WEP power supply: 100-240VAC)

Power consumption: Approx. 30VA

Connection: Terminal connection

Casing: Aluminum casting, drip-proof structure (conforming

to IEC529, IP65)

Weight: Approx. 4.3kg

Mounting: Bolt suspension method with 4 pieces of M8 bolts

CE-standards: EN61326-1:2006

Emission : Class A

Immunity : Table 2

SETTING DISPLAY UNIT

Input signal: RS485, up to 9 detectors connectable

Analog output: 4 to 20 mA DC, 3 output (Load resistance :

output 1, 2 : Less than 600Ω, 3 : Less than 400Ω)

(Component 1 of detector no.1 to 3 is outputed for

multi head)

Communications: RS232C(standard), RS422A or RS485(option)

Output renewal cycle:

28ms x detector number

Display: 1. Measured data, LED 5 digit

2. Detector No., component No., calibration curve

No., parameter setup

(Conponent No. is displayed for detector multicomponent

meter)

Detector No. setup: Detector No. 1 to 9 is key configurable

Component No. setup:

Component No. 1 to 4 is key configuable

(Depending on the detector)

Calibration curve No. setup:

Calibration curve No. is key configurable for each

of detector No. also configurable by external contact

Smoothing time: Smoothing time setting at smoothing calculation

T=0.0 to 9.9, 10 to 99 seconds

Calibration function: Perform calibration by key operation or by external

contact in use of checking plate

Hold / preset: Hold or preset the display and output by key

operation or by external contact

Calibration curve correction:

Online correction of calibration curve linear and

guadratic correction

External setup: Detector No., conponent No., calibration curve No.,

calibration, hold or preset

Alarm function: High/low limit alarm individual contact output (a

contact, common) beyond setting range

Self-diagnostic: Outputs contact signal(1b) when abnormal condition

Case material: Flame retardant polycarbonate

Working ambient: 0 to 50℃

Mounting: Panel-mount type

Weight: Approx. 0.6kg

Power supply: 100 to 240V AC 50/60Hz

Power consumption Max. 20VA

CE-standards: EN61326-1:2006

Emission : Class A

Immunity : Table 2

FIBER UNIT

Measuring distance and diameter:

With lens --- φ25/25mm to φ40/100mm

Without lens --- φ20/15mm to φ50/50mm

Fiber length: Standard 1.5m, Max.5m (Reflection type fiber)

Standard 2m, Max.10m (Transmission type fiber)

Fiber protection: Stainless steel flexible armour

Minimum bending radius:

R100mm

Working temperature:

0 to 150℃

Purge air flow: With lens --- Air purge disabled

Without lens --- 5 to 20L/min

Accessory: Vertical mounting holder

Flange holder


EXTERNAL DIMENSIONS



浏览了该产品的用户还浏览:

日本千野CHINO

千野CHINOKR2000系列

千野chino AL4、AH4系列混合式存储记录仪

新KP系列 数字式程序调节仪 设定器

混合式记录仪Ah3000(180mm)/Al3000(100mm)系列(笔式)

称重传感器客服
客服头部
称重传感器
称重传感器

扫一扫加微信公众号